Skip to main content

Hose – Cotton Synthetic Jacket, 1 1/2” NH X 3’, Rubber Lined

NFES #
000114
Category
Water Handling
Updated
Storage and Shelf Life Checks
None

Initial Inspection/Disposal Criteria

  1. Return to stock if hose is banded and in unused condition.
  2. Visually inspect for burns, cuts, damaged fittings.
  3. Inspect gasket for cracks, if any replace.
  4. Refurbish if item passes initial inspection.
  5. Dispose of hose if it fails initial inspection or fails Testing for Performance. Good couplings should be salvaged from hose that is not repairable.
  6. Recycle brass fittings from disposed hose.

Refurbishing Procedures

A. Testing for Performance

  1. Replace gasket if necessary.
  2. Connect female end of hose to pump or manifold:
    1. Confirm connection ends are not out of round and there is no damage to threads.
    2. All 1½” hose should be NH threads. 
  3. Pressure Test:
    1. Start pump.
    2. Make sure nozzles are open. Let all air escape from hose. Shut nozzles.
    3. Pressurize hose to 300 PSI and hold for 3 minutes.
    4. Inspect hose for the following which indicate a need for repair or disposal:  burns, cuts, or leaks between hose and couplings, at swivel portion of female coupling, and along the length of the hose.
  4. Female and male couplings:
    1. Inspect for leaks where hose goes into coupling.
    2. Inspect for crooked coupling (easier to see when hose is charged).
  5. Shut down pump and relieve water pressure from system.
  6. Remove hose.
  7. Stretch out good hose to drain.

B. Cleaning

  1. Clean excess dirt from hose.
  2. Run hose through hose washer using clean water or clean water with a mild detergent or clean with high pressure wash.
  3. If detergent is used, rinse with clean water.
  4. Allow hose to drain and dry completely before rolling.

C. Repair

  1. Repaired hose shall result in lengths that are a minimum of 90 percent of original length.
  2. Good couplings shall be salvaged from disposed hose.
  3. Re-coupling procedures.
    1. Remove old expansion ring and coupling from hose.
    2. Remove unserviceable portion of hose, squaring end to be re-coupled.
    3. Utilize expander machine to insert new expander and coupling. Follow specific machine operating instructions.
    4. Following re-coupling, hose that has been repaired or recoupled should be retested at a test pressure of at least 50 percent greater than the service test pressure following Testing for Performance above.

D. Repackaging

  1. Roll in a single roll configuration with male coupling in center of roll.
  2. Secure roll (plastic band, string).
  3. Local cache option for storage.
  4. Roll, secure, and place on pallet.

 

NWCG Latest Announcements

Quarter Three Materials for the 2025-2026 Wildland Fire Leadership Campaign Now Available

Date:  April 1, 2026
Questions? 
Please contact: Leadership Committee

NWCG is excited to announce that Quarter Three materials for the 2025/2026 Wildland Fire Leadership Campaign are now available. This annual initiative offers all students of leadership and wildland fire management an opportunity to engage with essential leadership skills and knowledge needed to lead effectively in dynamic environments.

Quarter Three materials focus on Leadership Level 3: Leader of People (Develop Intent). Leadership Level 3 is where your values, your team, and your influence come together. Leaders of People put their teams first, build trust, and lead with authenticity. They mentor future leaders and shape decisions up and down the chain.

References:

2025/2026 NWCG Leadership Campaign - Leadership Levels

Wildland Fire Leadership Development Program

Leadership Committee

WFSTAR 2026 Core Components Module Package and 2025 Fire Year in Review Now Available

Date:  March 23, 2026
Questions? 
Please contact: Joe Schindel

The 2026 Core Components Module Package for RT-130, Wildland Fire Safety Training Annual Refresher (WFSTAR) and the 2025 Fire Year in Review are now available on the NWCG website. The 2026 Core Components Module Package provides all content needed to deliver RT-130.

References:

2026 Core Components Module Package

2025 Fire Year in Review Module

NEW! S-490, Advanced Fire Behavior Calculations (Blended) Available Now

Date:  March 17, 2026
Questions? 
Please contact: Fire Behavior Subcommittee

NWCG is pleased to announce that the new S-490, Advanced Fire Behavior Calculations (Blended), 2026 course is now available.

This training includes performance-based activities that allow students to apply the knowledge and concepts required for the Fire Behavior Analyst (FBAN), Long Term Fire Analyst (LTAN), and Prescribed Fire Burn Boss Type 1 (RXB1) positions. It supports individuals working towards these incident qualifications.

This blended course begins with a self-paced online training (OLT) in the Wildland Fire Learning Portal (WFLP), followed by an in-person instructor-led training (ILT).

References:

S-490, Advanced Fire Calculations (Blended)

NWCG Fire Behavior Analyst (FBAN) Position Page

NWCG Long Term Fire Analyst (LTAN) Position Page

NWCG Prescribed Fire Burn Boss Type 1 (RXB1) Position Page

2024 Paul Gleason Award Winners Announced

Date:  March 13, 2026
Questions? 
Please contact: Leadership Committee

The NWCG Leadership Committee is proud to announce the recipients of the 2024 Paul Gleason "Lead By Example" awards. Award categories include Initiative and Innovation, Mentoring and Teamwork, Motivation and Vision, as well as a Lifetime Achievement Award.

Congratulations to the awardees:

  • Justin Baxter, National Unmanned Aerial System (UAS) Operations Specialist, with the U.S. Forest Service — Initiative and Innovation
  • Kelly Woods, Director of the Wildland Firefighting Lessons Learned Center — Mentoring and Teamwork
  • Doug Booster, Instructor, ProHealth Net, Inc. — Motivation and Vision
  • Pam McDonald, Writer-Editor for the National Interagency Fire Center — Lifetime Achievement Award

References:

Paul Gleason Lead By Example Award

Wildland Fire Leadership Development Program (WFLDP)

Leadership Committee