Skip to main content

PMS 448

PMS 448

Introduction

COVID-19 Refurb Guidelines

References

All Categories

Aviation

Camp

Clothing

Cordura

Fuel Handling

Kits

Medical

Miscellaneous

PPE

Small Engine Equipment

Tools

Water Handling

Deleted Items

Hose – Cotton Synthetic Jacket, 1 1/2” NH X 100’, Rubber Lined

NFES #
000967
Category
Water Handling
Updated
Storage and Shelf Life Checks
None

Initial Inspection/Disposal Criteria

  1. Segregate by NFES number.
  2. Visually inspect for burns, cuts, damaged fittings.
  3. Recycle brass fittings from disposed hose.
  4. Inspect gasket for cracks, if any replace.
  5. Return to stock if hose is banded and in unused condition.
  6. Refurbish if item passes initial inspection.
  7. Dispose of hose if it fails initial inspection or fails Testing for Performance.  Good couplings should be salvaged from any hose not repairable.

Refurbishing Procedures

A. Testing for Performance

  1. Replace gasket if necessary.
  2. Connect female end of hose to pump or manifold:
    1. Confirm connection ends are not out of round and there is no damage to threads.
    2. All 1½” hose should be NH threads. All 1” hose should be NPSH threads.
  3. Pressure Test:
    1. Start pump.
    2. Make sure nozzles are open. Let all air escape from hose. Shut nozzles.
    3. Pressurize hose to 300 PSI and hold for 3 minutes.
    4. Walk the length of the hose inspecting for the following which indicate a need for repair or disposal:  burns, cuts, or leaks between hose and couplings, at swivel portion of female coupling, and along the length of the hose.
  4. Female and male couplings:
    1. Inspect for leaks where hose goes into coupling.
    2. Inspect for crooked coupling (easier to see when hose is charged).
  5. Shut down pump and relieve water pressure from system.
  6. Remove hose.
  7. Stretch out good hose to drain.

B. Cleaning

  1. Clean excess dirt from hose.
  2. Run hose through hose washer using clean water or clean water with a mild detergent or clean with high pressure wash.
  3. If detergent is used, rinse with clean water.
  4. Allow hose to drain and dry completely before rolling.

C. Repair

  1. Repaired hose shall result in lengths that are a minimum of 90 percent of original length.
  2. Good couplings shall be salvaged from disposed hose.
  3. Re-coupling procedures.
    1. Remove old expansion ring and coupling from hose.
    2. Remove unserviceable portion of hose, squaring end to be re-coupled.
    3. Utilize expander machine to insert new expander and coupling. Follow specific machine operating instructions.
    4. Refurbished hose shall result in hoses that are 90 to 100 foot in length.
    5. Following re-coupling, hose that has been repaired or recoupled should be retested at a test pressure of at least 50 percent greater than the service test pressure following Testing for Performance above.

D. Repackaging

  1. Roll in a single roll configuration with male coupling in center of roll.
  2. Secure roll (plastic band, string)
  3. Local cache option for storage.
  4. Roll, secure, and place on pallet.
    • ​NFES #000932, #001238 - Cache option.  Recommended quantity per pallet 1” X 100’ length/pallet.
    • NFES #000933, #001239 - Cache option.  Recommended quantity per pallet 1½” X 100’ length/pallet.
    • NFES #000966, #000967 - Cache option quantity per pallet.

 

Reference

Water Handling Equipment Guide, PMS 447-1 

 

Print PDF

NWCG Latest Announcements

NEW! S-212, Intermediate Faller (Online) Course Available Now 

Date:  April 23, 2026
Questions? 
Please contact: Hazard Tree and Tree Felling Subcommittee

NWCG is pleased to announce that the new S‑212, Intermediate Faller (Online), course is now available on the Wildland Fire Learning Portal (WFLP). This second course in the series provides students with the knowledge and skills required to perform the duties of an Intermediate Faller (FAL2), as described in the FAL2 Incident Position Description. This course is intended for individuals seeking to advance from Basic Faller (FAL3) to FAL2.

S‑212, Intermediate Faller is a fully online, self‑paced training program consisting of 13 units. Learners will engage with interactive, scenario‑based content designed to progressively build foundational skills and knowledge essential for the FAL2 role.

Students must be qualified as a Basic Faller (FAL3) prior to enrolling in S‑212, Intermediate Faller course.

Any changes to qualification pathways will take effect with the next update of the NWCG Standards for Wildland Fire Position Qualifications, PMS 310-1, scheduled for January 2027.

References:

S-212 Intermediate Faller (Online)

RMC Memo 26-01: Transition Plan for Implementing Updates to Intermediate Faller (FAL2) Position Qualifications

Intermediate Faller (FAL2) Position Page

NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212

New Aircraft Flight Schedule Form, PMS 249

Date:  April 17, 2026
Questions? 
Please contact: National Coordination System Committee

A new publication from the National Coordination System Committee (NCSC) is now available. The NWCG Aircraft Flight Schedule Form, PMS 249, will be used for aviation crews and dispatch to share flight information that is needed for resource tracking, and if needed, for emergency procedures.

For further details, please contact your NCSC representative. 

References:

NCSC Memo 26-01: Implementation of NWCG Aircraft Flight Schedule Form, PMS 249

NWCG Aircraft Flight Schedule Form, PMS 249

New Glossary Term for Review

Date:  April 15, 2026
Questions? 
Please contact: Data Standards and Terminology Board (DSTB)

The Data Standards and Terminology Board is requesting feedback on a new glossary term: Resource Protection Measure (RPM).

The proposed definition is: Practical guidance provided for incident personnel in a manner in which incident objectives can be achieved while reducing impacts to identified resources across the landscape. RPMs are informed by, but not restricted to, Minimum Impact Strategies and Tactics (MIST).

Please review, share with your subgroups, and provide feedback as appropriate through the following form: Request Feedback The comment period will close May 10, 2026.

Thank you for your engagement in the NWCG glossary process – your participation is key to our success.

References:

Glossary Request Feedback

Quarter Three Materials for the 2025-2026 Wildland Fire Leadership Campaign Now Available

Date:  April 1, 2026
Questions? 
Please contact: Leadership Committee

NWCG is excited to announce that Quarter Three materials for the 2025/2026 Wildland Fire Leadership Campaign are now available. This annual initiative offers all students of leadership and wildland fire management an opportunity to engage with essential leadership skills and knowledge needed to lead effectively in dynamic environments.

Quarter Three materials focus on Leadership Level 3: Leader of People (Develop Intent). Leadership Level 3 is where your values, your team, and your influence come together. Leaders of People put their teams first, build trust, and lead with authenticity. They mentor future leaders and shape decisions up and down the chain.

References:

2025/2026 NWCG Leadership Campaign - Leadership Levels

Wildland Fire Leadership Development Program

Leadership Committee